Vegas CES Show 2016

James Tanner · « **on:** 5 Jan 2016, 04:10 am »

Hi Folks

At the show - will post some pics tomorrow.

james

Hicham · « **Reply #1 on:** 5 Jan 2016, 05:20 am »

Hi James,

Great, and elaborate too please, on the selected demonstration tracks for this all NEW Bryston B³ CUBED Series Amplifiers.
Thank you

tdinut · « **Reply #2 on:** 5 Jan 2016, 06:20 am »

Wishing you and Bryston a great show. Please keep up the awesome work and make us proud.

Rod_S · « **Reply #3 on:** 5 Jan 2016, 11:50 am »

Looking forward to the pics

redbook · « **Reply #4 on:** 5 Jan 2016, 04:20 pm »

dumanski · « **Reply #5 on:** 5 Jan 2016, 07:26 pm »

hoping to see the new 7b hot rods with there hoods open (the guts) if any maybe from production.

enjoy the show !

Shayne

James Tanner · « **Reply #6 on:** 6 Jan 2016, 04:14 am »

Some quick shots of the room

alexone · « **Reply #7 on:** 6 Jan 2016, 04:22 am »

James,

i guess these are either the 7B or the 28B. are the amps connected to the BIT??

al.

James Tanner · « **Reply #8 on:** 6 Jan 2016, 04:38 am »

Quote from: alexone on 6 Jan 2016, 04:22 am

James,

i guess these are either the 7B or the 28B. are the amps connected to the BIT??

al.

Hi Al

Yes the demo system is the BDP-2 with BDA3 into the BP26 then out to new 7B Cubed amps and driving Mini T's - all plugged into a BIT 20

james

jaydial · « **Reply #9 on:** 6 Jan 2016, 05:50 pm »

any new additions in the small form factor products?

James Tanner · « **Reply #10 on:** 9 Jan 2016, 01:06 pm »

Some nice pis at show courtesy of Dan:

Rod_S · « **Reply #11 on:** 9 Jan 2016, 01:24 pm »

Perhaps this is always the angle of the photos I've seen thus far but the left/right side sculpting/scalloping of the center elevated cube/square piece never seems to line up properly to the main panel sculpting/scalloping.

audio.bill · « **Reply #12 on:** 9 Jan 2016, 01:50 pm »

Rod - I see what you're referring to, but I think it only appears that way since the center panel protrudes a bit from the rest of the faceplate by design. Gives it a more 3D appearance.

James Tanner · « **Reply #13 on:** 9 Jan 2016, 02:19 pm »

Hi

Yes the Center panel is Proud of the rest of the faceplate.

james

James Tanner · « **Reply #14 on:** 9 Jan 2016, 02:28 pm »

Vegas CES Show 2016

James - your room sounded great. - Transparent is the way I would describe it

The Cube amps are awesome and so is the BDA-3.

You guys have been busy! The new phono and DC PSU are also very nice!

Great job!

Mike - AudioShark

Rod_S · « **Reply #15 on:** 9 Jan 2016, 06:31 pm »

Quote from: audio.bill on 9 Jan 2016, 01:50 pm

Rod - I see what you're referring to, but I think it only appears that way since the center panel protrudes a bit from the rest of the faceplate by design. Gives it a more 3D appearance.

That's good to know as something like that would bother me so much it would prevent me from purchasing.

Rod_S · « **Reply #16 on:** 9 Jan 2016, 06:37 pm »

So what's up next in the pipeline James? I know you had mentioned not to long ago about looking into getting the SP3 to accept above 44.1/16 via the USB. Is that still being looked into? I assume it would never accept DSD?? That would probably be a more substantial hardware upgrade and I suspect not worth it and would be something that would make more sense in the next platform when I suspect Atmos, dts:X and possibly Auro may make an appearance in a limited 16 channel or less configuration.

Rod_S · « **Reply #17 on:** 9 Jan 2016, 07:00 pm »

Something just occurred to me about Atmos, Auro and dts:X, does anyone know if these, particularly the ceilng channels can be properly setup without room EQ? I don't think I've come across anyone running such a setup that didn't have some form of EQ. If that is the case these would be non starters for Bryston.

Phil A · « **Reply #18 on:** 9 Jan 2016, 07:07 pm »

Quote from: Rod_S on 9 Jan 2016, 07:00 pm

Something just occurred to me about Atmos, Auro and dts:X, does anyone know if these, particularly the ceilng channels can be properly setup without room EQ? I don't think I've come across anyone running such a setup that didn't have some form of EQ. If that is the case these would be non starters for Bryston.

I'd guess not based on this - http://blog.dolby.com/2015/02/upgrade-home-theater-system-dolby-atmos/

and other things I've seen or heard about, although, of course, I have not seen or heard everything.

James Tanner · « **Reply #19 on:** 10 Jan 2016, 04:36 am »

Quote from: Rod_S on 9 Jan 2016, 06:37 pm

So what's up next in the pipeline James? I know you had mentioned not to long ago about looking into getting the SP3 to accept above 44.1/16 via the USB. Is that still being looked into? I assume it would never accept DSD?? That would probably be a more substantial hardware upgrade and I suspect not worth it and would be something that would make more sense in the next platform when I suspect Atmos, dts:X and possibly Auro may make an appearance in a limited 16 channel or less configuration.

Hi Rod

Yes the new USB for the SP3 will be able to do 192/24 and I believe with some small hardware changes DSD.

james