Service for Crossover Assembly, Wiring and Cables ETC. Southwest California Area

0 Members and 1 Guest are viewing this topic. Read 28980 times.

fre11111

  • Industry Participant
  • Posts: 161
Happy Saturday Everyone,

I have been busy with a bunch of projects over the past month, I have not taken photos of all of them. Here are a few of them!














Feel free to reachout if you need help with your project. Thank you. Godbless.

Frederick
frederickdelrosario111@gmail.com

SoCalWJS

Very nice work (as usual)!

I should swap out my CC for a bit and remove the x-over from my X Voce. Have the upgraded parts (somewhere). Problem is the other CC is buried in a storage locker and that is a daunting task. Can’t survive for long w/o my HT up and running.

May get to it at some point.  :green:

fre11111

  • Industry Participant
  • Posts: 161
Thank you.🙂🙏

fre11111

  • Industry Participant
  • Posts: 161
Hi Everyone,

I have been busy with many small projects but I wanted to share one of the newest upgrade that Danny did on the Monolith THX. Its alot of work and alot of parts. I had fun building this kit.









Happy Weekend.

Frederick
frederickdelrosario111@gmail.com
« Last Edit: 5 Sep 2023, 10:46 pm by fre11111 »

Danny Richie

Frederick, your work looks extremely nice.

fre11111

  • Industry Participant
  • Posts: 161
Thank you very much Danny. I appreciate it.

fre11111

  • Industry Participant
  • Posts: 161
Happy Tuesday,

I was not able to take photos of some xover restoration but I was able to take a photo of these.








Have a great week AC friends.

Frederick
frederickdelrosario111@gmail.com

Danny Richie

Nice work Frederick.

fre11111

  • Industry Participant
  • Posts: 161
Thanks Danny. I appreciate it.

rolandtk

  • Jr. Member
  • Posts: 3
Hi. Are you able to design an XO for
a GRS TR2 tweeter and Lavoce WSN041.00 4" Neodymium Woofer?
I can measure them in a cabinet with REW and umik mic.
If so kindly email me. Thanks.

Hobbsmeerkat

  • Industry Participant
  • Posts: 2516
Hi. Are you able to design an XO for
a GRS TR2 tweeter and Lavoce WSN041.00 4" Neodymium Woofer?
I can measure them in a cabinet with REW and umik mic.
If so kindly email me. Thanks.
Frederick just does crossover assembly.
Design work would require sending the drivers to Danny, installed into the cabinet  so we can design the crossover based on the actual acoustic output (4ms gated window) rather than electrical parameters or REW measurements alone which is a shot in the dark at best.


Tyson

  • Full Member
  • Posts: 11056
  • Audio - It's all a big fake.
Frederick just does crossover assembly.
Design work would require sending the drivers to Danny, installed into the cabinet  so we can design the crossover based on the actual acoustic output (4ms gated window) rather than electrical parameters or REW measurements alone which is a shot in the dark at best.

Lol, a shot in the dark, while blindfolded and spun around 3 times. 

fre11111

  • Industry Participant
  • Posts: 161
Hi. Are you able to design an XO for
a GRS TR2 tweeter and Lavoce WSN041.00 4" Neodymium Woofer?
I can measure them in a cabinet with REW and umik mic.
If so kindly email me. Thanks.


Hi Roland,

I sent a reply on your messages. Hobbs and Tyson are both correct and mimics the same reply I sent you. Goodluck on your project.

Frederick

fre11111

  • Industry Participant
  • Posts: 161
Hi Everyone,

I hope everyone is well. I have been busy with life and a bunch of projects. I just wanted to post some photos of GR RESEARCH kits I have finished. There are more and hopefully I can post them all...














May everyone have a blessed week,

Frederick
frederickdelrosario111@gmail.com




Jaytor

More beautiful work!

fre11111

  • Industry Participant
  • Posts: 161

fre11111

  • Industry Participant
  • Posts: 161
Hi Everyone,

Happy weekend. I just wanted to post some photo updates, some Gr Research upgrade kits and some other small projects. In some instances I have to disassemble the owners previous work and redo the whole crossover. It is alot of work to unsolder parts and with some luck not damage the parts.

This is a GR Research upgrade kit:





Here are the other photos of small projects:
















Happy Weekend. Godbless.

Frederick
frederickdelrosario111@gmail.com








fre11111

  • Industry Participant
  • Posts: 161
Hello everyone,

Happy weekend to my fellow AC people. I just wanted to post some photos of stuff in the works. External crossover for a Gr Research NX STUDIO  and another for a different GR Research speaker. All of these had premium parts provided by the owners.














Thank you. Godbless.

Frederick
frederickdelrosario111@gmail.com


maty


fre11111

  • Industry Participant
  • Posts: 161
Thank you.

Frederick