[A_shah]

Hello,
I am looking to get IC for QuickSliver Tube amp. Any recommendations would be appreciated
thank you !

Asghar
all power  outlets are PS audio outlets &  PS audio Dectet and noise harvesters in pairs .

Headphone Gear 
1. Gungnir DAC
2. Mojo (Hp)SS
3. Audeze Deck ard( HP)SS
4. QS Tube HP.

[witchdoctor]

Hello,
I am looking to get IC for QuickSliver Tube amp. Any recommendations would be appreciated
thank you !

Asghar

Headphone Gear 
1. Gungnir DAC
2. Mojo (Hp)SS
3. Audeze Deck ard( HP)SS
4. QS Tube HP.

I like the Mogami Gold which is used in the majority of recording studios. I also like Mapleshade a lot. Both are good value without crazy $$$ and very transparent.

I would also HIGHLY recommend trying the Mapleshade wall outlet to plug your gear into.

https://www.amazon.com/Mogami-GOLD-RCA-RCA-03-Contacts-Connectors/dp/B015NQGILK/ref=sr_1_1_sspa?keywords=mogami+gold+rca&qid=1549722195&s=gateway&sr=8-1-spons&psc=1&smid=A1NKUZPDBQC7DX

https://shop.mapleshadestore.com/Analog-Interconnects/products/87/

[ricmon]

I like the Mogami Gold which is used in the majority of recording studios. I also like Mapleshade a lot. Both are good value without crazy $$$ and very transparent.

I would also HIGHLY recommend trying the Mapleshade wall outlet to plug your gear into.

https://www.amazon.com/Mogami-GOLD-RCA-RCA-03-Contacts-Connectors/dp/B015NQGILK/ref=sr_1_1_sspa?keywords=mogami+gold+rca&qid=1549722195&s=gateway&sr=8-1-spons&psc=1&smid=A1NKUZPDBQC7DX

https://shop.mapleshadestore.com/Analog-Interconnects/products/87/

Ditto on the Mogami IC's.  I use them on my TT.

Ric

[Chris Adams]

Try these: http://audioenvy.com/product/home-car-pro-interconnects/nv-4s-pr-rca/

I just swapped out two sets of cables worth a little over 2k for these and I am blown away. They are effortless, clear, and fast. I have a pair of Quicksilver Mid Monos and an LTA Microzotl preamp.

They are returnable if you don't like them.

[A_shah]

Try these: http://audioenvy.com/product/home-car-pro-interconnects/nv-4s-pr-rca/

I just swapped out two sets of cables worth a little over 2k for these and I am blown away. They are effortless, clear, and fast. I have a pair of Quicksilver Mid Monos and an LTA Microzotl preamp.

They are returnable if you don't like them.

These look interesting
Asghar

[dspringham]

Try these: http://audioenvy.com/product/home-car-pro-interconnects/nv-4s-pr-rca/

I just swapped out two sets of cables worth a little over 2k for these and I am blown away. They are effortless, clear, and fast. I have a pair of Quicksilver Mid Monos and an LTA Microzotl preamp.

They are returnable if you don't like them.

Chris, are these particular (Studio - Prestige) cables available in XLR format?

Are you using their speaker cables and power cables as well? Any Feedback you would care to share?

Thanks,
Dave

[Chris Adams]

Chris, are these particular (Studio - Prestige) cables available in XLR format?

Are you using their speaker cables and power cables as well? Any Feedback you would care to share?

Thanks,
Dave

This is what you want: http://audioenvy.com/product/monitor/onestian-matched-pair/

I bought a complete loom, interconnects, speaker cable, and power cords. My system sounds so much more open, clear, and fast, not harsh, I just can't believe it. Not that what I had was bad, not at all. When I replaced two pair of interconnects and heard the difference, I ordered a replacement for every cable I had.

[Clsmooth391]

The Grover Huffman Pharaoh interconnects are the best I have tried. I've had the Teo Audio GameChanger Jnr and Cardas Clear.

[ketcham]

Zenwave D4/D5 series. (unshielded vs shielded)
Allnic ZL Technology Mu7R series

[FullRangeMan]

Headphones cables most be balanced, the sound quality is much better than the one (-) pole banana plug.

An audiophile suggestion:
http://apuresound.com/v3.html
An DIY suggestion:
Neotec UPOCC Teflon copper wire awg 20 + Neutric 4 pins XLR

[navi]

Hello,
I am looking to get IC for QuickSliver Tube amp. Any recommendations would be appreciated
thank you !

Asghar
all power  outlets are PS audio outlets &  PS audio Dectet and noise harvesters in pairs .

Headphone Gear 
1. Gungnir DAC
2. Mojo (Hp)SS
3. Audeze Deck ard( HP)SS
4. QS Tube HP.

Van Damme LoCap55 (best)  or their coaxial mic cable

[Jon L]

This is what you want: http://audioenvy.com/product/monitor/onestian-matched-pair/

I bought a complete loom, interconnects, speaker cable, and power cords. My system sounds so much more open, clear, and fast, not harsh, I just can't believe it. Not that what I had was bad, not at all. When I replaced two pair of interconnects and heard the difference, I ordered a replacement for every cable I had.

Their "back story" was an interesting read, and I really like their RCA connector design.
Usually, IME, cables that utilize low-mass, low-capacitance design tend to sound fast, airy, smooth but often not warm and dense.  How's that aspect of these Audio Envy cables? 

[Chris Adams]

I wouldn't call them warm and dense. However, I don't find them cool and thin. Of all the ICs I've tried/made, including some in the four figure range, these allowed the essence of each piece of gear upstream to flow unimpeded.

[SET Man]

Try these: http://audioenvy.com/product/home-car-pro-interconnects/nv-4s-pr-rca/

I just swapped out two sets of cables worth a little over 2k for these and I am blown away. They are effortless, clear, and fast. I have a pair of Quicksilver Mid Monos and an LTA Microzotl preamp.

They are returnable if you don't like them.

Hey!

    Those look very good, especially for the price I must say. Look like a simple no nonsense cable.

   A cheaper option than that would be to DIY. I actually built all the cables in my system myself... well, except the phono cable for my SME 3009 II improved tone arm. Funny how I ended up with a low capacitance cables that sounds similar to description of the one shown in the link with 6N OCC copper litz conductors 26ga if I remembered correctly, adhesive teflon tape and Eichmanna Bullet RCA plugs. These work and sound great in my all tubed system with SET amps. I got tired of paying so much money for cables.

   Anyway, to A_shah... don't go crazy over this and look for seller with full refund return policy so you get to try them in your own system.

Buddy

[Elizabeth]

One minor problem is no price range from the op.
As far as suggestions, each poster is going to off his or her own fav cable.
So I an NOT going to suggest any cable in particular. Just lend my bias to well known major market cable makers.
Audio Quest
Cardas
Kimber
And if you buy used... be aware a LOT of fake cables out there.

[FullRangeMan]

I have two copper/silver cables very well made by HifiMan site, both are inexpensive and good looking.

[ric]

Hi, I would recommend trying the Schroeder method, which is using a T or Y splitter to allow two sets of interconnects. You can buy a cheap pair of splitters on Ebay and if you hear a difference, get better quality splitters (I'm using some older Monster solid brass).
This is if you have two pair of ANY type of IC's. I used what I have on hand and the difference in sound quality is huge. I know it sounds nuts, but it works and doesn't cost much to implement. You can google Doug Schroeder method for more info....