[Triode Pete]

Here's a special TWL "Obsession NCF" power cord fitted with a Neutrik NAC3FC-HC powerCON 32 Amp Cable Connector.

This 7 ft. long "Obsession NCF" is going to an audiophile in Louisiana who just purchased a Synergistic Research Power Cell 8 SX power conditioner.





Cheers,
Pete

[Triode Pete]

This time, a custom-made HDMI - I2S cable following the PS Audio specification. This was for an audiophile connecting a PS Audio transport to a Holo Audio May DAC.





Cheers,
Pete

[Triode Pete]

For the holidays, a custom single stereo Spirit II XLR interconnect cable (male 4 pin to male 4 pin) for an audiophile in Indonesia...

This stereo interconnect will go between a Trafomatic Primavera SV 811 headphone amp into a Raal Requisite TI-1b Toroidal Transformer Ribbon Headphone Amplifier Interface.





Cheers,
Pete

[Triode Pete]

This time a set of Phono DIN to a pair of balanced XLR male outputs, for an audiophile in Oregon.





Cheers,
Pete

[Triode Pete]

This time around, a Custom "Obsession NCF" power cord fitted with the 32 amp Neutrik NAC3FC-HC powerCON cable connector. This is for a Gigawatt power conditioner.





Cheers,
Pete

[Triode Pete]

Here's a custom RCA output (from a turntable) to a XLR input (into a Phono preamp) for an audiophile in Hong Kong. This custom "Spirit II" Phono interconnect also has a separate ground wire with gold spades.





Cheers,
Pete

[Triode Pete]

Here's a custom-made 1.5m pair of RCA output (from a preamp) to XLR input (to mono block amplifiers) for an audiophile in Indonesia!





Cheers,
Pete

[Triode Pete]

This time around, a "Seven Plus" power cord fitted with upgraded Furutech FI-46 (G) NCF connectors!





Cheers,
Pete

[Triode Pete]

This time, a pair of Custom Balanced "Female XLR to a 1/4" TRS" cables for an audiophile in Canada. He's using this from his preamp into his Sublime Acoustic K231 electronic crossover.

For those who need to know, "TRS" stands for "TIP - RING - SLEEVE"... It carries balanced, low-noise audio signals, using three conductors (tip-ring-sleeve) mapped to XLR pins 1, 2, and 3.





Cheers,
Pete

[Triode Pete]

A ~ 6" "Freedom" ethernet cable 'Dongle' for an audiophile in Connecticut...



 

Cheers,
Pete

[Triode Pete]

This time around, a 0.5m pair of RCA Y-adapters, RCA male to two female RCA's, for an audiophile in Tennessee.



 

Cheers,
Pete

[gene9p]

hey Pete..just bought a new UST projector and it uses one of those tiny two prong, tiny holes power chord... I was using a TWL 10 with my last projector..very nice..any suggestions for this one?

[Triode Pete]

hey Pete..just bought a new UST projector and it uses one of those tiny two prong, tiny holes power chord... I was using a TWL 10 with my last projector..very nice..any suggestions for this one?

Hi Gene,
You have a Figure 8 IEC connector. I suggest an "Eleven Plus" power cord fitted with a Furutech FI-8n (G) IEC connector... See pic below...




Cheers,
Pete

[Triode Pete]

This time around a 0.75m pair of DC power cables for an audiophile customer in The Netherlands.

He'll be using these DC cables to connect a Volumio Rivo Plus streamer fed by a Keces P6 Linear Power Supply and a Silent Angel Bonn N8 network switch fed by a Keces P3 Linear Power Supply.

What's interesting is that both cables utilize different DC connectors on opposite ends, a 5.5mm / 2.5mm on the power supply ends and a 5.5mm / 2.1mm on the streamer/ network ends.





Cheers,
Pete

[Triode Pete]

A 6 ft. pair of custom TWL speaker cables, with premium Cardas CAB bananas on the amplifier end and special-order Furutech FP-201 spade connectors on the speaker side. The audiophile customer from California also specified a fairly light wire size of 14 AWG (normal TWL speaker cable is over twice the size at 10 AWG per leg).





Cheers,
Pete