[rollo]

Jason your beginning to impress me. Fine work Sir.


charles

[jtwrace]

Jason your beginning to impress me. Fine work Sir.


charles

Just starting?   

[rave959]

Holy sh!t!!!

 

Awesome build!

- Christian

Here are some NCore amps that I built. 

[bhakti]

Jason,

Awesome build!

Who did your front panel work and is the 'nCore' artwork publicly available?

I would like to do something similar, but smaller on a brushed aluminum face plate.

Thanks for sharing!

[jtwrace]

Jason,

Awesome build!

Who did your front panel work and is the 'nCore' artwork publicly available?

I would like to do something similar, but smaller on a brushed aluminum face plate.

Thanks for sharing!

Thanks.  There isn't any artwork per se.  The CAD operator draws it and creates what's called an IGES file. 

[bhakti]

OK - thanks!

[mr_bill]

Any chance of purchasing a pair of those faceplates?
Bill

[rascal]

Jason- amazing work! You should start your own bizness 

Since this (case) was your design/creation- any inputs on costs that went into it- you can PM me. I was considering Romeyn group buy but decided to defer my purchase of NC400 until fall when I have funds available 

[jtwrace]

Since this (case) was your design/creation-

It wasn't, you can purchase it here http://www.audiocircle.com/index.php?topic=106336.msg1088558#msg1088558

[OzarkTom]

It wasn't, you can purchase it here http://www.audiocircle.com/index.php?topic=106336.msg1088558#msg1088558

I believe what everyone is wondering here, where can you get and how much are those fancy NCORE faceplates? Is that at Sillicone Ray's too?

[jtwrace]

Is that at Sillicone Ray's too?

No, I made them.

[mjosef]

What's in the box?



Come on, what's in the box?




Four heads in a duffel-bag. 
Not my build, but did help putting it together. Its called Occam's Ncore build.
Nice thick solid case. Lots of room for future bridged modules.

[ted_b]

No, I made them.

??  Then wouldn't that be classified as "your design/creation"?  I'm very confused by your answers Jason, sorry.  You said they are not your creation and pointed us to the parts thread, then when asked if we could get (the faceplates) from Silicon Ray too, you said "no I made them".  ??

[a.wayne]

Whats the cost of the modules and Smps ... ?

[jtwrace]

??  Then wouldn't that be classified as "your design/creation"?  I'm very confused by your answers Jason, sorry.  You said they are not your creation and pointed us to the parts thread, then when asked if we could get (the faceplates) from Silicon Ray too, you said "no I made them".  ??

He asked about the cases right?

Since this (case) was your design/creation-

Then OzarkTom said he was asking about the face plates and that's when I said what I did about making them. 

Does that clear things up?

[jtwrace]

Whats the cost of the modules and Smps ... ?

https://www.hypexshop.com/

[a.wayne]

Thanks .....

[rascal]

Ok I have to rinse and repeat  , how much did faceplate cost? Seems like same set up Zybar has as well right? This is much better than Romeyn group buy etch.

[rascal]

Thank you Jason  .

Dumb question for you guys---I noticed on/off switch in couple of cases, and some did not. Do you need power on/off switch? Idle consumption is just around 5W right- and with soft start is a power on/off switch required?

Maybe this can go to 'Ask any question' thread in this forum

[Steidl Guitars]

Do you need power on/off switch?

Need?  No. 

Idle consumption is just around 5W right

A bit higher than that -- closer to 15w for each PS and amp-module pair when on and ready to play.