Gallery :: Slideshow

Gallery »
Slideshow

Gallery

X-MTM build plans	MDF panel cut plan for X-MTM	PL Max adhesive	Mockup spacer
Spacer thickness	PL glueing	Mockup assembly	Sectioned pieces
Cordless Router	Straight Edge #1	Straight Edge #2	Harbor Freight Clamps
Square corner	Rip Guide	Square saw blade	Old Craftsman router table
Table saw pre cut long piece	Precut top and bottom	Router pop out	Long piece routed
Long piece routed	Box dry fit	Side layout	Layout transfer to back panel
Sides, back and quarter rounds	Installing quarter round	Using bar spacer to install quarter round	Assembly w/ braces in place
Looking in from the backside	Oversized back panel	Cabinet parts	Glue selection
Butt gluing on MDF	Partial board vs MDF	Square cut	Whiteside down spiral trim cutter
Router bit description	Router circle cutter.	Router guides	Cut MDF
Tee nut in the front panel	Wrapped front panel	Removed pocket guide	Glueing pocket
Sides in place with glued pocket	Glue mess	glue on top and bottoms panels	Not enough clamps in the world
Got the front off	No drips, no hits, no errors	Picture frame corner clamps	3rd hand helpers
Glueing top plate on helpers	Picture frame corner clamps	3rd hand corner clamps	High corner clamp
Low corner clamp	Woodworking stuff	Router table with top panel	Dry fit of top/bottom panels
Top to side panel dry fit	Corner clamp interference	Router with rollers	Jon’s flat pack
More 3rd hand clamps	Oil on MDF	Oil soaked with paint thinner	Oil and paint thinner covered with baby powder
After 24 hrs of drying	After second application and 24 hr of drying	Layout for braces	Brace rails in place
Hole cutting practice	Sticky stuff	Brace rails stuck on	Sides with brace rails
Brad nailer clearance	Dry fit with braces	A braces	Replacement A brace
Double handled clamp	Cut off fixed end	Rest for long clamp	Fixing clamp spring
Feathering on hole cut	Up spiral cutter	Hole cutting in 10” brace	Almost through cut
Rounding brace hole edges	Holding pieces for routing	Half circle hole cutting	Wrapping the ends of the front panel
The wrap	Dried glue brush	Loose wrap	4 long clamps
6 long clamps	2nd speaker	Glueing	Separating front from sides
Residual glue	Cutting error	Test fit of back	Test fit of front
Gluing back 1	Gluing back II	Clamping back cab 2	Clamping back cab 1
Brace clamp	Modified glue bottle	Side clamps	Not enough clamping
Fixing the problem	Brace clamp	Crossover layout	Unboxing goodies
Practice hole cut for tweeter	Tweeter in practice hole	Crossover assembly	Crossover soldered 1
Crossover laid out	Crossover in the cabinet	Torch	Practice finish 1
Practice finish 2	Cutting No-Rez	No-Rez cutup	Installing No-Rez
No-Rez and crossover installed	Lining up holes for binding posts	Cutting holes in the front baffle	Done cutting holes
High end audio amplifier	With high end connections	High end bent wire connections	More connections
Buried Crossover	Template for insert nuts	Drilled holes for insert nuts	Front baffle ready to be glued in
Magnetic binding post parts	Current path through the magnetic parts	Non magnetic replacement parts	Binding posts
Back sanded	Rounding corners	Rounded corners	Flat black back
Staining	Improved finish	3rd coat of stain	30” snow fall
Snowblower triage	Finish 1	Finish 2	Wire crimping
up and running	completed speakers	base layout	Template layout
Old compass	Compass w pencil	Layout on plywood	Cut and sanded
Base painted and legs	Felt added	Speaker with base	classic Mini X-MTM