AudioCircle
Industry Circles => GR Research => Topic started by: Vince in TX on 15 Sep 2021, 10:24 pm
-
When I first hooked these up, stereo music playback wasn't all that impressive since I was running SVS PB-2000 Subs using LFE only combined with 20+ year old MP3 files from my aging digital library. So I put music playback on the back burner and focused on multi-channel surround for movies whilst I built the new subs (Servo Sub 4) and then the A/V-1RS surrounds. When I initially replaced the SVS subs with the Servo Subs, music playback was still lacking even though movies were amazing. And that's when I realized that during stereo music playback the subs were sitting at idle (no LFE channel in the tracks).
I had read here before that the best configuration for a theater was to use high-level input on the Servo Subs and put another sub (or two) at the back of the room on LFE, and that's exactly what I did. I connected the speaker cables from the AVR (soon from an Odyssey Kismet 3-channel amp that's on order) direct to the Servo Subs and jumpered them using leftover wire from my A/V-1RS build over to the X-Statics. Good Lord, what a difference! :o Even movie playback got better because all of the high-bitrate music tracks took full advantage of the Servo Subs (which was my initial concern with this configuration, and it turned out to be unfounded).
I sat back in my primary seating position, fired up some of those same stereo MP3s, closed my eyes and settled back into my theater seat. For the first time in my life, I was able to pick out all of the instruments and vocalists in 3D space. At first I thought the tracks tapped into the surrounds, but that wasn't the case. I was hearing full 3D from two speakers. And I don't even have the speaker placement or acoustical room treatments optimized yet (nor do I have the spiked feet on anything yet). As some wise old man once said, "You have taken your first step into a larger world."
Cue The Monkees: "I'm a Believer" :thumb:
(https://www.audiocircle.com/image.php?id=229737)
-
Ha ha!!! You ain't heard nuthin' yet -- wait until the Kismet arrives.
You made a very smart move by investing in good speakers. Now the rest of your system has to catch up to the level of quality that your speakers are capable of reproducing. I predict many more "aha" moments in your future.
-
Welcome to real hifi. :D
-
Hell yeah. Makes it all worth it.
-
Ha ha!!! You ain't heard nuthin' yet -- wait until the Kismet arrives.
You made a very smart move by investing in good speakers. Now the rest of your system has to catch up to the level of quality that your speakers are capable of reproducing. I predict many more "aha" moments in your future.
I seriously can't wait. I pre-wired the front L/R with two sets of 16/2 AWG (I should have gone 14/4 AWG) for the possibility of bi-amping them, but the X-Statics aren't bi-amp. So what I'm planning is to combine both 16AWG wires into a single wire tied to the RCA pre-amp on my Marantz SR8015 (which is actually impressive on its own).
And that brings up a question, what is everyone using for conversion from speaker wire to RCA? I was looking at these: https://www.amazon.com/TXK-Gold-Plated-Oxygen-Free-tin-Plated-Connecting/dp/B08XYK2TTM/ref=sr_1_7_sspa
-
And that brings up a question, what is everyone using for conversion from speaker wire to RCA? I was looking at these: https://www.amazon.com/TXK-Gold-Plated-Oxygen-Free-tin-Plated-Connecting/dp/B08XYK2TTM/ref=sr_1_7_sspa
Why do you need a speaker level to line level adapter?
-
And that brings up a question, what is everyone using for conversion from speaker wire to RCA? I was looking at these: https://www.amazon.com/TXK-Gold-Plated-Oxygen-Free-tin-Plated-Connecting/dp/B08XYK2TTM/ref=sr_1_7_sspa
I've never even heard of speaker wire to RCA... For analog playback after the preamp IMO the correct setup is either:
1) IF you have dual RCA outputs on your preamp, use one of the outputs to go to your speaker amps, and one to go to your subs using LINE IN (ideal).
2) If you do not have multiple outputs on your preamp, I would do dual speaker cables coming out of your amplifier, and hook them up to the HIGH LEVEL IN.
For HT playback I would use LFE with RCA's from your pre (it should have a subwoofer out or two). But, if you're going with option 2 above, I don't know how it plays together with both RCA's into LFE & HIGH LEVEL IN hooked up to speaker cables at the same time. I know LFE always prioritizes over LINE IN if it reads a signal. (I have HT bypass on my preamp and a separate HT only preamp, so there's no switching plugs around)
Of course YMMV as I haven't personally tried option 2.
-
Why do you need a speaker level to line level adapter?
My AVR is at the back of the room. It's roughly a 25' run. To convert from the standard high-level outputs to pre-out on the Marantz SR 8015 would need a conversion from standard two-wire to RCA.
(https://www.audiocircle.com/image.php?id=229781)
-
I've never even heard of speaker wire to RCA...
I actually linked to it above:
(https://www.audiocircle.com/image.php?id=229782)
For HT playback I would use LFE with RCA's from your pre (it should have a subwoofer out or two). But, if you're going with option 2 above, I don't know how it plays together with both RCA's into LFE & HIGH LEVEL IN hooked up to speaker cables at the same time. I know LFE always prioritizes over LINE IN if it reads a signal. (I have HT bypass on my preamp and a separate HT only preamp, so there's no switching plugs around)
I actually tried this, and it seemed to work. So rather than combine both cables, I would run one from pre-amp (using the RCA conversion) and the other from the high-level out to the subs? That might make more sense since I wouldn't need the Kismet to amplify the subs at all.
-
Then again, if you already have the subs hooked up with speaker cable (option 2), and only one preamp (for both 2 channel and HT) it's probably just easiest skipping LFE all together.
But then that brings up the question of room correction and Audyssey (or whatever people use), it wont think you have a subwoofer with the system since you won't have any RCA outs on your preamp hooked up. Not sure how well that plays together (haven't tried).
-
I actually linked to it above:
Understood! I should have said "I've never even heard of speaker wire to RCA until now" :lol:
-
Your sub amps have 2 inputs, either RCA or speaker level. If you're using the speaker level input, then you would use the speaker level output from your amps, no need to mess with the RCA connector at all.
If you are using the RCA level input on the sub amp, then you need a Y splitter between the Marantz and your Odyssey amps. Half the Y signal would go to the amps, the other half would go to the sub amps RCA input.
-
Then again, if you already have the subs hooked up with speaker cable (option 2), and only one preamp (for both 2 channel and HT) it's probably just easiest skipping LFE all together.
But then that brings up the question of room correction and Audyssey (or whatever people use), it wont think you have a subwoofer with the system since you won't have any RCA outs on your preamp hooked up. Not sure how well that plays together (haven't tried).
I actually do have a subwoofer with LFE in the system. It's at the back of the room now. :thumb:
So this is my plan (I think - for now):
- High-level direct to the servo subs (skipping LFE)
- Pre-Amp using 2-wire to RCA conversion for L/R/C to the Odyssey
- Odyssey to the L/R/C speakers
Your sub amps have 2 inputs, either RCA or speaker level. If you're using the speaker level input, then you would use the speaker level output from your amps, no need to mess with the RCA connector at all.
If you are using the RCA level input on the sub amp, then you need a Y splitter between the Marantz and your Odyssey amps. Half the Y signal would go to the amps, the other half would go to the sub amps RCA input.
Interesting. I'll take this into consideration also. I suppose I'll have to play with the different wiring options when the amp shows up.
Thanks for the feedback!
-
RCA output to speaker level input won't work. The signal is going to be way to low for the speaker level input.
-
RCA output to speaker level input won't work. The signal is going to be way to low for the speaker level input.
No, no. I would convert speaker wire to RCA at both ends. Basically I'd be turning a 25' speaker wire into a 25' RCA connection.
-
No, no. I would convert speaker wire to RCA at both ends. Basically I'd be turning a 25' speaker wire into a 25' RCA connection.
Oh you mean in order to have a larger gauge to avoid signal loss. Ah, that's interesting. Yeah that will probably work.
-
Oh you mean in order to have a larger gauge to avoid signal loss. Ah, that's interesting. Yeah that will probably work.
Yes! That's what I was thinking. The Odyssey would go at the front of the room beneath the screen. And something just dawned on me. I can combine both sets of 16 AWG speaker wires (they are AudioQuest SLiP 16/2) into a single wire, convert to RCA at both ends and go direct from the Marantz pre-amp to the Odyssey. Then I can go from the speaker out on the Odyssey to the high-level on the Rythmik amps for the L/R channels and jumper from there to the X-Statics like I have now. :D
Incidentally, I don't think I've ever posted the latest on the equipment cubby. Last picture showed everything sitting on their respective boxes:
(https://www.audiocircle.com/image.php?id=229786)
(https://www.audiocircle.com/image.php?id=229785)
-
You know, another possibility (which might end up being more trouble than it's worth) is to just yank out all of the existing wiring in that front channel and start over. I ran it through conduit for this very reason. I just recall how much of a pain in the butt it was to pull two sets of 16/2 (three in the case of the left tube to cover the center channel) + an RG6 for LFE through that 1" tube. A single 14/4 on the Right, then a 14/4 and 14/2 (Center) on the left would have been a cakewalk in comparison.
Live and learn.
(https://www.audiocircle.com/image.php?id=229787)
-
Vince -- let me save you some heartache down the road -- keep your HT and budding 2-channel system separate. They should only share the front speakers. Use the Kismet for your 2-channel system and buy a good preamp. That 3rd channel on your Kismet may come in handy later on. Trust me -- you're gonna separate movies from music either now or later. May as well save time and money by doing it now.
-
Vince -- let me save you some heartache down the road -- keep your HT and budding 2-channel system separate. They should only share the front speakers. Use the Kismet for your 2-channel system and buy a good preamp. That 3rd channel on your Kismet may come in handy later on. Trust me -- you're gonna separate movies from music either now or later. May as well save time and money by doing it now.
Believe it or not, this was Plan B if I couldn't solve the wiring challenges. I was contemplating a nice turntable to go with it. It would be nice to not have to swap cables around, though. Right now, my music library is accessed with my Apple TV through a Plex server, and everything is controlled with a Savant Pro (one remote to rule them all).
-
My AVR is at the back of the room. It's roughly a 25' run. To convert from the standard high-level outputs to pre-out on the Marantz SR 8015 would need a conversion from standard two-wire to RCA.
(https://www.audiocircle.com/image.php?id=229781)
You don't convert from the preamp out RCA to speaker wire. The preouts on your AVR are designed to be connected to a power amp or another preamp with an HT by-pass input which is then connected to a power amp. The power amp has the speaker binding posts which are connected to the high level inputs of the sub amps and to the speaker binding posts. This can either be done by connecting two pairs of wires to the power amp's binding post and running one pair to the speakers and the other pair to the sub amps or run one pair from the power amp to either the sub amp or the speakers and daisy chaining a second wire to the part not connected to the power amp.
If you want to keep low frequencies from the amp powering the speakers you need an inline filter between the preamp and power amp. The filter needs two legs per channel. One leg has a cap that will limit the low frequencies going to the power amp and the other leg is a by-pass that sends a full range signal to the sub amp.
This is how I had my Marantz SR7008 (and now have an Arcam AV40 preamp/processor) connected. The preamp outputs of the Marantz (now Arcam) are connected to the HT by-pass input of my two channel preamp. This preamp is connected to an inline filter with by-pass legs. The filtered legs are connected to the monoblocks and the by-pass legs are connected to the RCA inputs of the sub amps.
The AV-1/RS surround speakers are connected to the AVR (AV/Pre-Pro) surround speaker terminals and the sealed servo sub is connected to the AVR (Pre-Pro) LFE/sub RCA pre-out connection.
When listening to two channel music, the two channel preamp is connected to whatever source I'm listening to and it controls the main volume. When watching a movie, the two channel preamp is set to the HT by-pass input. This allows the AVR/Pre-Pro to control the main volume.
For my type of setup to work, you need a two channel preamp with an HT by-pass setting or know at what volume position the two channel preamp is at unity gain. If your preamp does not have added gain (either a passive or active unity gain) the needed volume setting is full on/wide open. If your preamp does not have an HT by-pass input and has a gain stage, you need to know the volume setting where the preamp is at unity gain. For example, if your preamp has a volume control that goes from 0 to 100, and the company says the unity gain position is 76, set the volume at 76 when using that input. If your preamp has an HT by-pass input, that should automatically be set at unity gain.
-
You don't convert from the preamp out RCA to speaker wire.
I was planning to use RCA on both ends of that speaker wire to convert it from a high-level output/input to a low-level pre-amp interconnect between the AVR at the back of the room and the Odyssey amp at the front of the room. Alternatively, I could just put the Odyssey at the back of the room with the rest of the equipment and use short RCA interconnects between the AVR and the Odyssey.
...The preouts on your AVR are designed to be connected to a power amp or another preamp with an HT by-pass input which is then connected to a power amp. The power amp has the speaker binding posts which are connected to the high level inputs of the sub amps and to the speaker binding posts. This can either be done by connecting two pairs of wires to the power amp's binding post and running one pair to the speakers and the other pair to the sub amps or run one pair from the power amp to either the sub amp or the speakers and daisy chaining a second wire to the part not connected to the power amp.
This daisy-chain is exactly how it's hooked up now with the binding posts on the AVR going to the high-level on the sub amps, then daisy-chained to the X-Statics.
If you want to keep low frequencies from the amp powering the speakers you need an inline filter between the preamp and power amp. The filter needs two legs per channel. One leg has a cap that will limit the low frequencies going to the power amp and the other leg is a by-pass that sends a full range signal to the sub amp.
Any filter recommendations, links, or wiring diagrams? I'm a visual thinker, so it's difficult for me to picture it. :)
This is how I had my Marantz SR7008 (and now have an Arcam AV40 preamp/processor) connected. The preamp outputs of the Marantz (now Arcam) are connected to the HT by-pass input of my two channel preamp. This preamp is connected to an inline filter with by-pass legs. The filtered legs are connected to the monoblocks and the by-pass legs are connected to the RCA inputs of the sub amps.
The AV-1/RS surround speakers are connected to the AVR (AV/Pre-Pro) surround speaker terminals and the sealed servo sub is connected to the AVR (Pre-Pro) LFE/sub RCA pre-out connection.
When listening to two channel music, the two channel preamp is connected to whatever source I'm listening to and it controls the main volume. When watching a movie, the two channel preamp is set to the HT by-pass input. This allows the AVR/Pre-Pro to control the main volume.
For my type of setup to work, you need a two channel preamp with an HT by-pass setting or know at what volume position the two channel preamp is at unity gain. If your preamp does not have added gain (either a passive or active unity gain) the needed volume setting is full on/wide open. If your preamp does not have an HT by-pass input and has a gain stage, you need to know the volume setting where the preamp is at unity gain. For example, if your preamp has a volume control that goes from 0 to 100, and the company says the unity gain position is 76, set the volume at 76 when using that input. If your preamp has an HT by-pass input, that should automatically be set at unity gain.
Wow. That's a lot to digest. Can you believe that in 30 years of playing with this stuff, I've never used an AVR as a pre-amp? So much to learn.
Interestingly enough, I was just shopping for 2-channel pre-amps. Any recommendations? I actually had my eyes on a Marantz ND8006.
-
Using speaker wire as an interconnect is a terrible idea. A 25’pair of Blue Jeans LC-1 is only $130 and will sound a lot better.
-
I was planning to use RCA on both ends of that speaker wire to convert it from a high-level output/input to a low-level pre-amp interconnect between the AVR at the back of the room and the Odyssey amp at the front of the room. Alternatively, I could just put the Odyssey at the back of the room with the rest of the equipment and use short RCA interconnects between the AVR and the Odyssey.
It's not the connectors that convert from a low level to a high level signal. The power amp does that. What you want to run from the AVR preamp out at the back of the room to the Odyssey amp at the front of the room is a well shielded RCA interconnect, not speaker wire. When I did this with single ended connections like you have, I used 25' Douglas Connections Bravo interconnects https://douglasconnection.com/product/douglas-connection-analog-interconnect-cables/ You have to contact Doug for lengths greater the 15'.
Any filter recommendations, links, or wiring diagrams? I'm a visual thinker, so it's difficult for me to picture it. :)
Here's a pic of one I built using an electrical box from a big box store, Cardas RCA chassis connectors, and Sonicap Platinum caps.
(https://www.audiocircle.com/image.php?id=229799)
The legs going through the caps are the filtered legs. The input side is connected to the preamp and the output side to the power amp. The value of the cap depends on the input impedance of the power amp and the frequency of the rolloff.
The leg coming out the side of the box is the full signal by-pass leg which goes to the low level input of the sub amp.
Interestingly enough, I was just shopping for 2-channel pre-amps. Any recommendations? I actually had my eyes on a Marantz ND8006.
My current two channel preamp is a PS Audio BHK signature preamp. Before that it was a PS Audio Stellar Gain Cell DAC (which is both a preamp and a DAC but the DAC doesn't have to be used if you have one you like better. Before that my two channel preamp was a DODD Audio battery powerd tube buffer.
However, these are all just preamps except for the Stellar which also has a DAC. Price wise the Stellar GCD is close to the Marantz ND8006 but does not have the CD and streaming capability of the Marantz.
-
Interestingly enough, I was just shopping for 2-channel pre-amps. Any recommendations? I actually had my eyes on a Marantz ND8006.
Get a real preamp, man. Grab an Odyssey Tempest to mate with the Kismet.
-
First off, well said, Mike! Much more concise explanation than mine. I do the same as you, except don’t use an inline filter for high pass, and have dual outputs on my Dodd, instead of dual outputs on your shnazzy high pass box :thumb: was thinking of making a similar one without the additional output, then I went down the line of: should I just stick it on an RCA and expose it, then what RCAs to get, then should I just do a whole set of DIY RCA cables while I’m at it (which I’d love advice on!) or should I put the capacitor directly in the amp itself…. And so on. So I end up doing nothing :lol:
Get a real preamp, man. Grab an Odyssey Tempest to mate with the Kismet.
I can attest to the Odyssey Candela. It’s a wonderful preamp, that of course has perfect synergy to the Odyssey amps. That was my first “real preamp”, coming from my HT preamp, an Emotiva UMC-200. It was certainly not a minor step up… it also has HT bypass and (usually?) dual outputs. I had mine sitting in my basement for about 4 years, and I just sold it a few months ago. Of course UPS destroyed it. Klaus got her all fixed up tho! :thumb:
I’d also suggest eventually getting either monoblocks or a stereo amp for your front two speakers, and using the 3 channel for center and rears… there’s always upgrades, it’s never ending :D
-
It's not the connectors that convert from a low level to a high level signal. The power amp does that. What you want to run from the AVR preamp out at the back of the room to the Odyssey amp at the front of the room is a well shielded RCA interconnect, not speaker wire.
I wasn't planning low level to high level. I was planning low level to low level with RCA connectors on both ends of the speaker cable. But the one thing missing that you mentioned with this scenario is the shielding, which makes sense.
When I did this with single ended connections like you have, I used 25' Douglas Connections Bravo interconnects https://douglasconnection.com/product/douglas-connection-analog-interconnect-cables/ You have to contact Doug for lengths greater the 15'.
Thanks! Those look like good cables.
Here's a pic of one I built using an electrical box from a big box store, Cardas RCA chassis connectors, and Sonicap Platinum caps.
(https://www.audiocircle.com/image.php?id=229799)
The legs going through the caps are the filtered legs. The input side is connected to the preamp and the output side to the power amp. The value of the cap depends on the input impedance of the power amp and the frequency of the rolloff.
The leg coming out the side of the box is the full signal by-pass leg which goes to the low level input of the sub amp.
Good stuff, thanks!
My current two channel preamp is a PS Audio BHK signature preamp. Before that it was a PS Audio Stellar Gain Cell DAC (which is both a preamp and a DAC but the DAC doesn't have to be used if you have one you like better. Before that my two channel preamp was a DODD Audio battery powered tube buffer.
However, these are all just preamps except for the Stellar which also has a DAC. Price wise the Stellar GCD is close to the Marantz ND8006 but does not have the CD and streaming capability of the Marantz.
I don't necessary need the CD player. I'm planning to just update my ancient low-res MP3s with fresh CD rips from my CD library as raw 44.1 KHz, and then look into high-res audio files or streaming (not to mention the possibility of LP).
Very much appreciated! :thumb:
Get a real preamp, man. Grab an Odyssey Tempest to mate with the Kismet.
I'll also look into the Odyssey. I've been waiting on the Kismet since April, though, so that may have to wait for a future upgrade.
-
I'll also look into the Odyssey. I've been waiting on the Kismet since April, though, so that may have to wait for a future upgrade.
Why wait? Here ya go: https://www.canuckaudiomart.com/details/649750450-odyssey-tempest/
-
I don't necessary need the CD player. I'm planning to just update my ancient low-res MP3s with fresh CD rips from my CD library as raw 44.1 KHz, and then look into high-res audio files or streaming (not to mention the possibility of LP).
If your interest is playing digital files from a music server (computer) and/or streaming through the server the PS Audio Stellar Gain Cell DAC is a very good option. It sells new outright for $1,900 but you can trade in equipment and get up to 30% off bringing the new price to $1,330. This was the preamp/DAC I had in my room at the last Lone Star Audio Fest. The only reason I'm not still using it is that I upgraded to the the PS Audio BHK preamp and DirectStream DAC Sr. It's worth considering.
-
If your interest is playing digital files from a music server (computer) and/or streaming through the server the PS Audio Stellar Gain Cell DAC is a very good option. It sells new outright for $1,900 but you can trade in equipment and get up to 30% off bringing the new price to $1,330. This was the preamp/DAC I had in my room at the last Lone Star Audio Fest. The only reason I'm not still using it is that I upgraded to the the PS Audio BHK preamp and DirectStream DAC Sr. It's worth considering.
I agree that the PSA Stellar Gain Cell/DAC is a great piece of equipment. It serves both preamp and DAC duties in my system (with their M700 monoblocks driving Maggie .7s) and I love it. I feed data to its DAC from a NuPrime CDT-8 Pro and a Node 2i (soon to be replaced with an Aurender N100H).
-
Why wait? Here ya go: https://www.canuckaudiomart.com/details/649750450-odyssey-tempest/
Woah. That's a pretty good deal. I just pinged the seller to see if it has the HT Bypass option.
EDIT: Actually, even if it doesn't, I just pinged Klaus to see if he could upgrade it if it doesn't. I'd send it to him to go through regardless. Thanks for the link!
-
I just want to "+1" a few things said recently
+1
Separate the 2 channel audio and get yourself 2-channel preamp + amp. Those A/V receivers are really built with "decoding all the formats" first and foremost in mind.
+1
The cheapest cable you want to go with is BlueJeans cable. It's cheap + quality and LOTS of bang for the buck.
I would also add.... Try to use CD's or Hi-res instead of mp3s.
Apologies, I know that sounds "preachy" and that's not how I intend it. I'm excited for you Vince. You have some fun ahead of you!!
-
I just want to "+1" a few things said recently
+1
Separate the 2 channel audio and get yourself 2-channel preamp + amp. Those A/V receivers are really built with "decoding all the formats" first and foremost in mind.
+1
The cheapest cable you want to go with is BlueJeans cable. It's cheap + quality and LOTS of bang for the buck.
I would also add.... Try to use CD's or Hi-res instead of mp3s.
Apologies, I know that sounds "preachy" and that's not how I intend it. I'm excited for you Vince. You have some fun ahead of you!!
Not preachy at all! I'm still brand new to the audio world, especially hi-fi, beyond Plug & Play with an AVR. Deepest I'd ever dove previously was manually balancing my system with an SPL meter. Now I have a UMIK-1 balanced microphone, REW software, I'm researching cables, digging into understanding room calibration and acoustic treatments, etc. This is a multi-year journey for sure. Thanks for the feedback! I looked at the BlueJeans site and fully intend to pick up my RCA cables from them. :thumb:
Oh, and, yes. If you looked up the Specs of my Marantz SR8015, "decoding all formats" is an understatement. This thing is 8K ready on top of decoding any and every multi-channel movie format imaginable. It will serve its movie duty admirably.