AudioCircle
Audio/Video Gear and Systems => Headphone Mania => Topic started by: JohnR on 11 Nov 2016, 04:31 am
-
I'm wondering if anyone here has replaced the "screw in" type sockets in a pair of Hifiman's with the newer 2.5mm type?
Or happens to have bookmarked a link to someone doing it? (I'm sure I've seen it but I'm unable to find it now.)
I'm fed up with them as the plugs on the cable seem to keep breaking.
-
Sometimes the sockets are also glued down so require a bit more grunt to remove. There's not much to it other than being careful (seriously, don't let a screwdriver slip towards the magnets/diaphragm).
If you're going to all that trouble though, you may as well hardwire or do a mini-xlr socket. That's far far better than a 2.5mm TRS.
-
Hi, thanks for the response. I guess I just assumed mini-XLR wouldn't fit, but I'll order some mini-XLR sockets and see how they look. If I'm going to modify them, may as well do it right, as you say ;) I located a used pair of HD-600s to tide me over while I work on them.
-
Check with norne audio. They sell lots of different connectors and may have some insights.
-
How long have you had these? Should you really have to "re-engineer" them? I have heard the 560's and was fairly impressed, but stories like this one (design and/or QC problems) seem to be common regarding Hifiman products. I'd contact the manufacturer before performing "surgery" on them even if they are no longer in warranty. Maybe you can get some satisfaction.
-
I have heard the 560's and was fairly impressed,
Its said the HE560 has a neutral sound, according the personal taste some would say cold, not the warm harmonics presentation from the HE400.
-
How long have you had these? Should you really have to "re-engineer" them? I have heard the 560's and was fairly impressed, but stories like this one (design and/or QC problems) seem to be common regarding Hifiman products. I'd contact the manufacturer before performing "surgery" on them even if they are no longer in warranty. Maybe you can get some satisfaction.
Hi, I don't have to "re-engineer" them, the headphones themselves are fine. However the matching plugs that go onto the cables keep breaking (as I said) and they are a pain to work on. Nobody has ever liked them, and Hifiman have I guess implicitly acknowledged this by changing to 2.5mm TRS connectors sometime since I bought this pair a bit over 2 years ago.
Obviously, I like them or I wouldn't have kept them this long... or be interested in modifying them :)
I did contact Hifiman and they want $230 to replace the sockets with the newer types.
-
Check with norne audio.
Well they do have these:
http://www.norneaudio.com/litzheim/norne-hyper-short-audeze-lcd-2-3-x-xc-hifiman-he-5-6-560-adapters?search=hifiman
I guess that's one way to go....
I took the grills off and there is not enough room to directly mount a miniXLR, it would need to be mounted in an external thing, kinda the way Audeze do it.
-
Well they do have these:
http://www.norneaudio.com/litzheim/norne-hyper-short-audeze-lcd-2-3-x-xc-hifiman-he-5-6-560-adapters?search=hifiman
I guess that's one way to go....
I took the grills off and there is not enough room to directly mount a miniXLR, it would need to be mounted in an external thing, kinda the way Audeze do it.
Nothing a dremel and/or stepped drill bit wouldn't fix... :thumb:
Or just hardwire and don't even bother with connectors. The fewer the better!
-
No, there is not enough room :) The amount of space on the ... big round thing... between the driver and the edge of it is not enough for a mini-XLR.
If you hardwire, how do you fasten the cable to stop it moving? (To avoid stress on the leads to the drivers)
-
Well they do have these:
http://www.norneaudio.com/litzheim/norne-hyper-short-audeze-lcd-2-3-x-xc-hifiman-he-5-6-560-adapters?search=hifiman
I guess that's one way to go....
I took the grills off and there is not enough room to directly mount a miniXLR, it would need to be mounted in an external thing, kinda the way Audeze do it.
If you're not comfortable physically modifying them, which is understandable, maybe make a short adapter - 2.5mm receptacle to male hifiman, one for each side. Then if you tug too hard on the cable, it'll just pull out the trs plug.
Hifiman sells the coax connector. I doubt they're anything special - digikey probably sells them and adapters if you can figure out exactly what kind of coax connector they are.
These mention adapting, I'd reach out to norne audio (very friendly) and ask for their advice
http://www.norneaudio.com/litzheim/Furutech-Valab-Oyaide-Shure-Denon-diy-headphone-cable-connector?product_id=43
-
No, there is not enough room :) The amount of space on the ... big round thing... between the driver and the edge of it is not enough for a mini-XLR.
If you hardwire, how do you fasten the cable to stop it moving? (To avoid stress on the leads to the drivers)
I could have sworn I've seen mods that had the mini-xlr's, but my recollection is fuzzy. For sure I've seen it on the older style cups (HE-4/5/6).
My HE-6's are hardwired, and it's just simply glue and a couple layers of heat shrink that hold it in place.
-
I did contact Hifiman and they want $230 to replace the sockets with the newer types.
:o
-
Right, well I didn't jump on it. But you know, I wasn't really expecting them to even offer that, they're a business and need to stay in business. I'd prefer if this thread could focus on my actual question, thanks ;)
-
My HE-6's are hardwired, and it's just simply glue and a couple layers of heat shrink that hold it in place.
Hm. OK... interesting.
If you're not comfortable physically modifying them, which is understandable, maybe make a short adapter - 2.5mm receptacle to male hifiman, one for each side. Then if you tug too hard on the cable, it'll just pull out the trs plug.
I'm not sure I want a pigtail arrangement because it still means having the plugs in place, which is what I'm trying to not have. The hardwired adapter might be immune to breaking like the ones I have. I suppose I should post a pic. Anyway I've had an idea about how to mount the mini XLRs. Will try something when i get them.
-
This is more of an FYI than a solution to the OP's issue. Hope that's OK.
Hifiman has the 560's on sale for $700. And the 400i's for $250 (wow!)
-
Sure, no worries ;) That's a great deal!!
I haven't had time to think about this the last week. However I got a response from Norne saying no reported issues with the adapters I linked, so I'm thinking I might just go that way.
-
Any decisions or pictures?
-
Ha, time takes time :) I've just ordered a pair of the Norne adapters and will see how that goes.
-
I don't seem to be having much luck in getting Norne to actually ship me a pair of those adapters, so I may go back to the modding idea.
-
I don't seem to be having much luck in getting Norne to actually ship me a pair of those adapters, so I may go back to the modding idea.
Thats odd and sucks. I've had really helpful conversations with them/him.
-
Overloaded it seems. Anyway he did give me a refund and I've sourced a pair of adapters from an alternate source: http://www.ebay.com.au/itm/182262519108
-
Been using the adapters for a little bit now. Just chopped the ends off my existing Hifiman cable and soldered on some cheap 4-pin XLRs. They work well, the combined adapter+connector could potentially bump into your shoulders if you hunch or have a short neck or are wearing a lot of winter clothing. But so far so good, glad I got 'em :thumb:
(http://www.audiocircle.com/image.php?id=160502)
(http://www.audiocircle.com/image.php?id=160503)
-
Just updating this, been a bit over a month, the adapters are working nicely, I can focus on other things for now. Hard to recommend them as a permanent solution as I still have to be a bit careful about positioning the headphones on my head. Also the left screw connector still works loose, just as it did when I was using SMC cables.... there's a reason Hifiman ditched those connectors... I still intend to do the mod and fit miniXLRs to the headphones eventually. Just not a high priority.